DEWEConfig

+ + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +

2019-08-20 Release Notice DEWEConfig v3.6.1

Configuration tool for DEWETRON DAQP/HSI amplifiers.

*Version: 3.6.1

* Components:

** DEWEConfig 3.6.1

** LabVIEW Runtime engine 2016 32 bit

** NI-VISA Runtime 17.5

* Requirements:

** in case of RS232 from PC COM Port:  Windows 10 64-Bit or Windows 7 64/32-Bit

** in case of RS485 from DEWETRON DAQ: DEWETRON DAQ driver ≥ 2.1.0.0 and Windows 7 64/32-Bit

** in case of RS485 from DEWETRON DSA: DEWETRON DSA driver ≥ 4.1.0.0 and Windows 7 64/32-Bit

* Installation Procedure:

** Run installer with default settings

* Supported Hardware

** DAQP-ACC-A, DAQP-CHARGE-B, DAQP-DMM, DAQP-HV, DAQP-LA, DAQP-LA-SC, DAQP-LV, DAQP-MULTI, DAQP-V, DAQP-V-A, DAQP-V-B, DAQP-STG, DAQP-THERM, DAQP-CFB2, DAQP-CHARGE-A, DAQP-FREQ-A 

** HSI-HV, HSI-LV, HSI-STG

** PAD-TH8-P + PAD-CB-xxx, PAD-V8-P, EPAD-TH8-x, EPAD-V8, EPAD-RTD8

** DAQP-LA2-B-S6 (will be displayed as DAQP-LA-SC)

* Not Supported Hardware

** DAQP-FREQ, DAQP-BRIDGE-A, DAQP-BRIDGE-B, DAQP-ACC

** legacy PAD modules (PAD-TH8, PAD-V8 with GREEN LED), PAD-DO7, PAD-DI8, PAD-RTD3

* New Features and most important bugfixes:

** Bugfix for input range unit calculation and scaling factor

* Known Limitations:

** Custom range support for DAQP-STG and HSI-ST: only symmetric custom ranges (no offset)

** In case of RS485 from DEWETRON DSA/DAQ: no support of Windows 10 64 Bit

** No support of customized DAQP-LA modules other than V100 and V110

** No support of custom ranges (except DAQP-THERM, DAQP-Multi and DAQP-CHARGE-B)

** No auto setup of amplifiers according TEDS settings from MSI and TEDS enabled sensors

** DAQP-LA2-B-S6 will be displayed as DAQP-LA-SC (pinout image incorrect)

** Multilanguage support covers most elements, but not all. Tip strips and help yet in English only.

+ + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +
2023-11-24 Release Notice DEWETRON Config 4.3
Configuration tool for DEWETRON DAQP/HSI amplifiers.
*Version: 4.3

* Components:
** DEWETRON Config 4.3
** LabVIEW Runtime engine 2016 
** NI-VISA Runtime 17.5

* Requirements:
** Windows 10 64-Bit
** Windows 11 64 bit 

* Installation Procedure:
** Run installer with default settings

* Supported Hardware
** DAQP-STG (incl Custom Range settings)
** All other modules are not tested!

* Changes
** Configurable timeouts via ini-File for Custom Range settings for DAQP-STG modules to prevent an issue with FW 1.80

2019-11-07 Release Notice DEWETRON Config 4.2
* Version 4.2

* Changes
** DAQP-STG Custom Ranges added
** Possibility to configure several racks on different COM port