High-precision front-ends for analog signal conditioning
TRIONet3 is a compact front-end solution for synchronous high-speed data acquisition across great distances and distributed locations. The front-end system communicates via Ethernet or USB 3.0 bus and can be operated intuitively with our software OXYGEN.
The TRIONet3 can be connected to any Windows computer via either USB or Ethernet. Alternatively, TRIONet3 systems are high-speed channel expansions for other DEWETRON DAQ systems and can be interconnected using Ethernet.
On the front, there are two TRION(3) module slots that can be equipped with TRION3 or TRION modules as required. Thus, the flexible TRIONet3 can be turned into the smallest power analyzer in just a few steps.
Note: TRIONet and TRIONet3 devices use the same firmware!
Measurement systems for your PC via Ethernet or USB
Connect DEWETRON’s front-end systems to your computer via USB or Ethernet interface, to become a powerful data acquisition system. The systems are distributable and can be daisy-chained to a multi-channel measurement system. Every common sensor is supported by using our special MSI sensor adapters.
You have to be logged in to access the downloads. Please use the login form on the top of the page.
## Description:
TRIONet software release supporting TRIONet3 and TRIONet devices.
Please note that downgrades to older software versions are only possible by USB stick.
## New Features and most important bugfixes:
* TRIONet3 device support
* TRION(3)-1820-MULTI:
* Input coupling (highpass filter) overshoot fixed with 0.15Hz filter
* TRION(3)-Power:
* TRION SUB-XV support added
* TRION3-SUB-8:
* TRION SUB-XV support added
## Known Limitations
* None
TRIONet Firmware R6.7.1: Create new USB update stick
(01_TRIONet_R6.7.1_Create_USB-stick.zip - 228.22 MB) md5: d431e20767d01bc09fcfaa7d153c74ee
## Requirements
* All TRIONet devices used with OXYGEN should be updated to the image included in this release
## New Features and most important bugfixes:
* Software Update: Fixed an issue when software update did not succeed
* IP Config: Set factory default IP address to DHCP with autoip (LL) fallback
* TRION driver fix for last 32bit addressable page (Debian Linux OS)
TRIONet Firmware R6.7.2: Create new USB update stick
(01_TRIONet_R6.7.2_Create_USB-stick.zip - 230.82 MB) md5: af3d153dab780a499d5e4149cbb92567
## Requirements
* All TRIONet devices used with OXYGEN should be updated to the image included in this release
## New Features and most important bugfixes:
* TRION(3)-18xx-MULTI Highpass Filters (0.16Hz - 100Hz) is distorting the input signal
* trion_cal: TRION-18XX-MULTI, allow AUTO and 0Hz for HP-Filter in XML
## Known Limitations
* ID001 - TRION(3)-18xx-MULTI Highpass Filters (0.16Hz - 100Hz) show 64% overshoot and higher cutoff frequencies than expected
TRIONet Firmware R7.0.0: Create new USB update stick
(01_TRIONet_R7.0.0_Create_USB-stick.zip - 234.46 MB) md5: 79d1ae896273f876ba841cc56115b9eb
## New Features and most important bugfixes:
* Allow device network configuration even if ip settings do not match
* Node default name is the serial number
* Fix: ID001 - TRION(3)-18xx-MULTI Highpass Filters (0.16Hz - 100Hz) show 64% overshoot and higher cutoff frequencies than expected
* Fix: ID002 - TRION(3)-18xx-MULTI Highpass Filters (0.16Hz - 100Hz) is distorting the input signal
## Description:
TRIONet software release supporting TRIONet3 and TRIONet devices.
Please note that downgrades to older software versions are only possible by USB stick.
## New Features and most important bugfixes:
* TRIONet3 device support
* TRION(3)-1820-MULTI:
* Input coupling (highpass filter) overshoot fixed with 0.15Hz filter
* TRION(3)-Power:
* TRION SUB-XV support added
* TRION3-SUB-8:
* TRION SUB-XV support added
## Known Limitations
* None
TRIONet Firmware R6.7.1: Update files for existing USB stick
(02_TRIONet_R6.7.1_Update_existing_USB-stick.zip - 205.26 MB) md5: 3d6cef0939eb3b0681f0ce48d671c8c7
## Requirements
* All TRIONet devices used with OXYGEN should be updated to the image included in this release
## New Features and most important bugfixes:
* Software Update: Fixed an issue when software update did not succeed
* IP Config: Set factory default IP address to DHCP with autoip (LL) fallback
* TRION driver fix for last 32bit addressable page (Debian Linux OS)
TRIONet Firmware R6.7.2: Update files for existing USB stick
(02_TRIONet_R6.7.2_Update_existing_USB-stick.zip - 207.86 MB) md5: 6837239c225e060b80a332179f69cb36
## Requirements
* All TRIONet devices used with OXYGEN should be updated to the image included in this release
## New Features and most important bugfixes:
* TRION(3)-18xx-MULTI Highpass Filters (0.16Hz - 100Hz) is distorting the input signal
* trion_cal: TRION-18XX-MULTI, allow AUTO and 0Hz for HP-Filter in XML
## Known Limitations
* ID001 - TRION(3)-18xx-MULTI Highpass Filters (0.16Hz - 100Hz) show 64% overshoot and higher cutoff frequencies than expected
TRIONet Firmware R6.7.3: Update files for existing USB stick
(02_TRIONet_R6.7.3_Update_existing_USB-stick.zip - 210.48 MB) md5: 1f1b31e3308b0217de0a918840226701
Version: R6.7.3 Releasedate: 2024-02-14
TRIONet Firmware R7.0.1: Update files for existing USB stick
(02_TRIONet_R7.0.1_Update_existing_USB-stick.zip - 211.51 MB) md5: e5f0e53f82912d3a48f542e48d749a2d
## Description:
TRIONet software release supporting TRIONet3 and TRIONet devices.
Please note that downgrades to older software versions are only possible by USB stick.
## New Features and most important bugfixes:
* TRIONet3 device support
* TRION(3)-1820-MULTI:
* Input coupling (highpass filter) overshoot fixed with 0.15Hz filter
* TRION(3)-Power:
* TRION SUB-XV support added
* TRION3-SUB-8:
* TRION SUB-XV support added
## Requirements
* All TRIONet devices used with OXYGEN should be updated to the image included in this release
## New Features and most important bugfixes:
* Software Update: Fixed an issue when software update did not succeed
* IP Config: Set factory default IP address to DHCP with autoip (LL) fallback
* TRION driver fix for last 32bit addressable page (Debian Linux OS)
## Requirements
* All TRIONet devices used with OXYGEN should be updated to the image included in this release
## New Features and most important bugfixes:
* TRION(3)-18xx-MULTI Highpass Filters (0.16Hz - 100Hz) is distorting the input signal
* trion_cal: TRION-18XX-MULTI, allow AUTO and 0Hz for HP-Filter in XML
## Known Limitations
* ID001 - TRION(3)-18xx-MULTI Highpass Filters (0.16Hz - 100Hz) show 64% overshoot and higher cutoff frequencies than expected
## New Features and most important bugfixes:
* Allow device network configuration even if ip settings do not match
* Node default name is the serial number
* Fix: ID001 - TRION(3)-18xx-MULTI Highpass Filters (0.16Hz - 100Hz) show 64% overshoot and higher cutoff frequencies than expected
* Fix: ID002 - TRION(3)-18xx-MULTI Highpass Filters (0.16Hz - 100Hz) is distorting the input signal
## New Features and most important bugfixes:
* Fix: ID001 - TRION(3)-18xx-MULTI Highpass Filters (0.16Hz - 100Hz) show 64% overshoot and higher cutoff frequencies than expected
* Fix: ID002 - TRION(3)-18xx-MULTI Highpass Filters (0.16Hz - 100Hz) is distorting the input signal
## New Features and most important bugfixes:
* Fix: ID001 - TRION(3)-18xx-MULTI Highpass Filters (0.16Hz - 100Hz) show 64% overshoot and higher cutoff frequencies than expected
* Fix: ID002 - TRION(3)-18xx-MULTI Highpass Filters (0.16Hz - 100Hz) is distorting the input signal
## Requirements
* Update all TRION modules to the latest firmware included in this release
* Use OXYGEN R7.2.0 or higher
* Windows 10 64-Bit or better
## Installation procedure
* Install TRION applications
* Reboot system (if requested by the installer)
* Start DEWETRON Explorer and update each TRION board firmware to latest version (right-click on enclosure name)
* Power-cycle TRION boards (Power down system, then restart)
* Start DEWETRON Explorer and check for a successful firmware upgrade
## Fixes
* NEX[DAQ]-1000 simulation sample rate divider support fixed.
## Requirements
* Update all TRION modules to the latest firmware included in this release
* Use OXYGEN R7.2.0 or higher
* Windows 10 64-Bit or better
## Installation procedure
* Install TRION applications
* Reboot system (if requested by the installer)
* Start DEWETRON Explorer and update each TRION board firmware to latest version (right-click on enclosure name)
* Power-cycle TRION boards (Power down system, then restart)
* Start DEWETRON Explorer and check for a successful firmware upgrade
## Fixes
* NEX[DAQ]-1000 simulation sample rate divider support fixed.